Worksheets · AP Physics 1

AP Physics 1 Unit 2 Free Response: Forces and Dynamics

Four original free-response questions on Unit 2, one of each kind on the exam, with a scoring guide and a printable PDF with room to write, free to use in class. Good practice before the Unit 2 Progress Check in AP Classroom. Multiple choice for this unit: Unit 2 worksheet.

Sigma Prep · sigmaprep.io/worksheets/ap-physics-1

Name

AP Physics 1 Unit 2 Free Response: Forces and Dynamics

Date Version A

Directions: Answer each part in the space below it. Show your work: the principle or equation you start from, the values you use and your reasoning. A justification needs a physics reason, not just an equation. Give numerical answers with units. A calculator and the AP Physics 1 equation sheet may be used throughout; use g = 9.8 m/s². The four questions are worth 40 points.

Free response: a calculator and the equation sheet are allowed.

Questions 1–4
  1. Question 1: Mathematical Routines (10 points)
    1.
    A mapping probe of mass m travels in a circular orbit of radius r, measured from the center of the Moon, which has mass M. The gravitational force from the Moon is the only force exerted on the probe.
    1. (a)
      Derive an expression for the probe's orbital speed v. Express your answer in terms of M, r, and physical constants, as appropriate. Begin your derivation by writing a fundamental physics principle or an equation from the reference information.
    2. (b)
      Derive an expression for the period T of the orbit in terms of M, r, and physical constants, as appropriate. Begin your derivation by writing a fundamental physics principle or an equation from the reference information.
    3. (c)
      The probe orbits 4.60×105 m above the surface. The Moon has mass 7.35×1022 kg and radius 1.74×106 m. Calculate the period of the orbit. Use G=6.67×10−11 N⋅m2/kg2.
    4. (d)
      A second mapping probe is placed in a circular orbit whose radius is 9 times as large. A student says its period is 9 times as long, because it has 9 times as far to travel around. Do you agree? Use your expressions from parts (a) and (b) to justify your answer.
  2. Question 2: Translation Between Representations (12 points)
    2.
    A light vertical spring of spring constant k stands on the floor. A block of mass m is held on top of it so that the spring has its natural length, and is then released from rest. The block moves down, compressing the spring, stops for an instant at its lowest point, and moves back up. Air resistance is negligible.
    1. (a)
      The left dot stands for the block at position P, halfway between the equilibrium position and the lowest point, on its way down; the right dot stands for the block at its lowest point. On each dot, draw the forces (not components) exerted on the block. Draw each force as an arrow that begins on the dot and points away from it, and label it. Make the lengths of the arrows show how the sizes of the forces compare. Use the same scale for both dots.

      Figure 1

      Position PLowest point
    2. (b)
      The block can also rest on the spring at its equilibrium position. Derive an expression for the spring's compression xeq there, in terms of m, k, and physical constants, as appropriate. Begin your derivation by writing a fundamental physics principle or an equation from the reference information.
    3. (c)
      The block has mass 0.20 kg and the spring has k=80 N/m. The spring is replaced with one that has four times the spring constant, and the block rests on it. Calculate how far the new spring is compressed. Use g=9.8 m/s2.
    4. (d)
      A student says that at the lowest point, where the block is momentarily at rest, the net force on the block is zero. Do you agree? Justify your answer by referring to your diagram from part (a) and to how the block's velocity changes at the lowest point.
  3. Question 3: Experimental Design and Analysis (10 points)
    3.
    A student wants to determine the coefficient of kinetic friction between a cart with locked wheels and a level table. The equipment available is a force sensor, held level so that it pulls horizontally on the cart, a balance, and a set of masses that can be added to the cart.
    1. (a)
      Describe a procedure the student could use to collect data that could be graphed to determine the coefficient of kinetic friction. Indicate the quantities measured and the equipment used to measure each.
    2. (b)
      Describe one way the student could reduce the uncertainty in the experimental value of μk.
    3. (c)
      The student collects the data shown in the table.

      Table 1

      m (kg)F (N)
      0.503.4
      1.006.8
      1.5010.0
      2.0014.0
      2.5016.0
      3.0020.0
      Here m is the total mass of the cart and any added masses, and F is the force sensor's reading while the cart slides at a constant speed. Indicate which quantities could be graphed to yield a straight line whose slope could be used to determine μk. You may use the remaining columns of the table for any quantities you calculate.
    4. (d)
      On the grid, plot the data for the quantities indicated in part (c). Label both axes with the quantities and their units, use linear scales, and draw a best-fit line.

      Figure 1

    5. (e)
      Using the best-fit line, calculate an experimental value for μk.
  4. Question 4: Qualitative/Quantitative Translation (8 points)
    4.
    A uniform rope of mass m and length L hangs straight down from a hook in a ceiling, and a crate of mass M hangs at rest from the rope's lower end.
    1. (a)
      Is the tension in the rope just below the hook greater than, less than, or equal to the tension just above the lower end? Justify your answer in a short paragraph, without equations.
    2. (b)
      Derive an expression for the tension in the rope at a height y above its lower end. Express your answer in terms of M, m, y, L, and physical constants, as appropriate. Begin your derivation by writing a fundamental physics principle or an equation from the reference information.
    3. (c)
      Is your expression from part (b) consistent with your answer to part (a)? Justify your answer by comparing the tension it gives at the two ends of the rope. Also describe what it gives for a rope of negligible mass.

      End of Version A

Free AP Physics 1 worksheets at sigmaprep.io/worksheets/ap-physics-1Original questions written by Sigma Prep. AP is a registered trademark of the College Board, which is not affiliated with this sheet.

Scoring guide · Version A

Question 1Mathematical Routines · Topic 2.9 · 10 points

(a) 3 points Derivation

  • 1 point: Starts from Newton's second law, taking the gravitational force as the net force.
  • 1 point: Uses the centripetal acceleration v2r.
  • 1 point: Correct result v=GMr.

Also acceptable: For point 3: Any algebraically equivalent expression.

Model answer

Gravity is the net (centripetal) force: GMmr2=mv2r, so v=GMr.

(b) 2 points Derivation

  • 1 point: Substitutes the speed into T=2πrv, consistent with part (a).
  • 1 point: Correct result T=2πr3GM.

Also acceptable: Either route earns points 1 and 2: Newton's second law with a=ω2r and ω=2πT, GMmr2=m(2πT)2r. For point 2: Any algebraically equivalent expression.

Model answer

One orbit is a distance 2πr at speed v: T=2πrv=2πr3GM.

(c) 2 points Calculation

  • 1 point: Uses the orbit radius measured from the Moon's center, r=2.20×106 m.
  • 1 point: Correct value, consistent with part (b): 9260 s for the correct expression.

Also acceptable: For point 2: A value that rounds to the same answer to two or three significant figures, with correct units. Either route earns point 2: the speed from part (a) and T=2πrv, or ω=GMr3 and T=2πω.

Model answer

r=(1.74×106 m)+(4.60×105 m)=2.20×106 m, so T=2πr3GM=2π(2.20×106 m)3(6.67×10−11 N⋅m2/kg2)(7.35×1022 kg)=9260 s.

(d) 3 points Claim and justification

  • 1 point: Disagrees with the student (the student's period is too short).
  • 1 point: Compares the orbital speeds, consistent with part (a): smaller at the larger radius for the correct v∝1r.
  • 1 point: Finds the new period, consistent with part (b): 27 times as long for the correct T∝r3/2.

Also acceptable: Earns point 3: the path 9 times as long at one-third the speed, so the period is 9×3=27 times as long.

Model answer

No. The path is 9 times as long, but the wider orbit is also slower: by part (a), v∝1r, so the speed is 13 as large. By part (b), T∝r3/2, so the period is 93/2=27 times as long.

Question 2Translation Between Representations · Topic 2.8 · 12 points

(a) 4 points Free-body diagram

  • 1 point: Fs up and Fg down on each dot, and no other force (the point needs all three on both dots: Fs up, Fg down and no other force).
  • 1 point: Fg the same length on both dots.
  • 1 point: At P the spring force is longer than Fg.
  • 1 point: At the lowest point the spring force is longer than Fg and longer than the spring force at P (the point needs both).

Note: A force counts only when it is labeled, and a diagram with any extra force earns at most 3 points. The ratios of the arrows' lengths may vary: points 3 and 4 grade only which arrow is longer.

Model answer

On each dot, Fs up (the spring) and Fg down, with Fg the same length on both. By Hooke's law the spring force kx grows with the compression x, and it equals Fg at the equilibrium position. P is below the equilibrium position, where the spring is compressed more, so at P the spring force is longer than Fg. The spring is compressed most at the lowest point, so there the spring force is longer than Fg and longer than at P.
Position PFsFgLowest pointFsFg

(b) 3 points Derivation

  • 1 point: Starts from Newton's second law for the block at rest: Fs=Fg.
  • 1 point: Uses Hooke's law for the spring force, Fs=kxeq.
  • 1 point: Correct result xeq=mgk.

Also acceptable: For point 3: Any algebraically equivalent expression.

Model answer

At rest the block's acceleration is zero, so by Newton's second law the forces on it balance: Fs=Fg. With Hooke's law, Fs=kxeq, and Fg=mg: kxeq=mg, so xeq=mgk.

(c) 2 points Calculation

  • 1 point: Substitutes the given values for the new spring constant 4k, consistent with part (b): x=mg4k for the correct expression.
  • 1 point: Correct value, 0.0061 m.

Also acceptable: For point 2: A value that rounds to the same answer to two or three significant figures, with correct units.

Model answer

From part (b) with the new spring constant 4k: x=mg4k=(0.20 kg)(9.8 m/s2)4(80 N/m)=0.0061 m.

(d) 3 points Claim and justification

  • 1 point: Disagrees with the student (the net force at the lowest point points up).
  • 1 point: Uses the diagram, consistent with part (a): the spring force longer than Fg at the lowest point for a correct diagram.
  • 1 point: Reasons from the motion: the velocity changes from downward to upward at the lowest point, so the acceleration points up (the point needs both).

Model answer

No. At the lowest point the spring force is longer than Fg in part (a), so the net force points up. That fits the motion: there the block's velocity changes from downward to upward, so its acceleration, and with it the net force, points up, even though the block is at rest for an instant.

Question 3Experimental Design and Analysis · Topic 2.7 · 10 points

(a) 4 points Experimental procedure

  • 1 point: Measures m with the balance.
  • 1 point: Uses at least five different total masses m.
  • 1 point: Measures the pull F with the force sensor.
  • 1 point: Pulls the cart at a constant speed (checked by watching that the cart does not speed up or slow down).

Note: Keeping the reading steady without a constant speed does not earn point 4 (a steady pull larger than the friction force speeds the cart up).

Model answer

Add masses to the cart to make at least five different total masses m, measuring each with the balance. For each one, pull the cart along the level table with the force sensor at a constant speed, watching that the cart does not speed up or slow down, and record the sensor's steady reading F. With a=0 the net force on the cart is zero, so this reading equals the kinetic friction force.

(b) 1 point Reducing uncertainty

  • 1 point: Repeated trials at each setting, averaged.

Also acceptable: For point 1: More data points (more masses) or a wider range of masses.

Model answer

Repeat each trial several times and average the measurements.

(c) 1 point Linearizing data

  • 1 point: Graphs F against m (either quantity may be on either axis).

Also acceptable: For point 1: Another pair: F against mg (either quantity may be on either axis).

Model answer

Graph F on the vertical axis and m on the horizontal axis. At constant speed the pull balances kinetic friction: F=μkmg, so F is proportional to m. So the slope is μkg.

(d) 3 points Graphing data

  • 1 point: Both axes labeled with the quantities and their units, with linear scales (the point needs both).
  • 1 point: Data points plotted correctly, consistent with part (c).
  • 1 point: A single straight best-fit line, not a line joining the points.

Model answer

The points lie close to a straight line through the origin. The best-fit line passes through the grid points (0,0) and (3.5 kg,23 N).
00.51.01.52.02.53.03.50510152025m (kg)F (N)

(e) 1 point Value from the best-fit line

  • 1 point: Correct value from the slope of the best-fit line, μk≈0.67 (the slope is μkg), consistent with part (c).

Also acceptable: A slope read from two points on the student's own best-fit line (a data point that lies on the line may be one of them); the value that follows from that slope earns the value point when it falls in the accepted range. For point 1: Accepted range for the value: 0.64 to 0.70 (5% either way of the guide's value, 0.67). Also for point 1: With another pair from part (c): the value from that pair's own slope relation (for F against mg, μk=slope; for mg against F, μk=1slope; for m against F, μk=1g(slope)).

Model answer

The slope of the best-fit line is (23−0) N(3.5−0) kg≈6.57 N/kg, found from the origin and the point (3.5 kg,23 N). Because the slope is μkg, μk=slopeg=6.57 N/kg9.8 m/s2=0.67.

Question 4Qualitative/Quantitative Translation · Topic 2.3 · 8 points

(a) 3 points Claim and justification

  • 1 point: Claims the tension is greater at the top.
  • 1 point: Each part of the rope is in equilibrium, so the tension above a point balances the weight of everything below it (the point needs both).
  • 1 point: The rope's own weight adds to what the upper part supports.

Model answer

Greater than. Treat a piece of rope as the system: it is at rest, so the rope above it must pull up on it with a force equal to the weight of everything it supports. Near the lower end the rope supports only the crate; just below the hook it supports the crate and the weight of the whole rope as well. Because the rope has mass, the tension grows going up.

(b) 3 points Derivation

  • 1 point: Applies equilibrium to everything below the point as one system.
  • 1 point: The mass of rope below the point is yLm.
  • 1 point: Correct result T=Mg+mgyL.

Also acceptable: For point 3: Any algebraically equivalent expression.

Model answer

Below that point hang the crate and a length y of rope, whose mass is yLm. They are at rest, so T=Mg+yLmg, that is, T=Mg+mgyL.

(c) 2 points Consistency check

  • 1 point: Answers yes, the expression is consistent with part (a): T=Mg at y=0 and (M+m)g at y=L for the correct expression (the point needs all three: the answer and both values, from which greater at the top follows).
  • 1 point: With m=0 (a rope of negligible mass), the tension is Mg at every height.

Also acceptable: Earns point 1: with a part (a) claim of equal or less, the two end values its own part (b) expression gives and an answer of no; in every case point 1 is judged against the response's own part (a) claim and part (b) expression.

Model answer

Yes. At the lower end (y=0) it gives T=Mg, and at the hook (y=L) T=(M+m)g, which is larger, as claimed in part (a). With m=0 it gives T=Mg everywhere: a light rope has the same tension along its length.

What does the AP Physics 1 free response ask on Unit 2?

Questions about this set

Since 2025 the free-response section has four questions, one of each kind: Mathematical Routines (10 points: derive and calculate, then a claim with a justification), Translation Between Representations (12 points: draw a diagram, bar chart or graph, derive, and connect the representations), Experimental Design and Analysis (10 points: a procedure, a linear graph from data and a value from its slope), and Qualitative/Quantitative Translation (8 points: reason without equations, derive, then check that the two agree). This set has one of each, in that order.

Points are earned for specific pieces of work: starting from a correct principle, an expression in the requested symbols, a value with units, a sketch with the right shape, a claim with its physics reason. The scoring guide lists every point and what earns it, other acceptable methods, and a model answer for each part. On the exam the free response is half of the score.

Yes, throughout, as on the exam: a calculator and the AP Physics 1 equation sheet are allowed on both sections. Use g = 9.8 m/s², the value on the equation sheet.

No. Every question is original, written by Sigma Prep in the format of the exam. Before the set was published, an independent checker re-derived every expression, recomputed every value and its units, and read every graph and diagram back from the drawing.

The progress check is College Board's own end-of-unit quiz in AP Classroom, assigned by your teacher, and its free-response questions are not public: we do not have them, and Sigma Prep is not affiliated with College Board. This set is exam-style practice on the same unit: one question of each kind on the exam, with a scoring guide that says what earns each point. Write your answers in full, score them with the guide, then redo the parts that lost points.

Yes: the Unit 2 multiple-choice worksheet, and the mixed free-response set, which is laid out like a full free-response section with each question on a different unit.

AP is a registered trademark of the College Board, which was not involved in making this set and does not endorse it. All questions are original to Sigma Prep. Frozen 2026-11-19.